Skip to content

Dimension key

Read the foundation bolts dimensions

Identify the pattern first. A DIN 529 Type B cranked anchor is not the same geometry as a J hook, an L bend or a straight anchor rod with an end plate. The drawing should separate overall length, exposed projection, thread length and embedment. Include nut/washer arrangements, sleeves, plates and the template hole layout so the complete bolt set can be checked.

Download dimensions and RFQ datasheet (PDF)

Foundation Bolts dimension identification schematic; not to scale

Standard size reference

DIN 529 Type B anchor bolt reference dimensions

Standard thread and anchor-head references help identify a specified pattern. Customer drawings control complete foundation assemblies; custom layouts have no preassigned dimensions on this page.

Reference: DIN 529 Type B Dimensions in mm; nominal reference values
DIN 529 Type B anchor bolt reference dimensions – DIN 529 Type B
Thread D Pitch P Anchor width A Minimum thread b
M8 1.25 24 20
M10 1.5 30 25
M12 1.75 36 30
M16 2 48 40
M20 2.5 60 50
M24 3 75 60
M30 3.5 95 75
M36 4 115 90

This table applies only to the DIN 529 Type B cranked-anchor reference. It must not be used as a J-bolt or L-bolt bend schedule. Overall length, embedment, projection, template spacing and assembly details follow the customer's approved design. Dimensions alone do not establish concrete-anchor resistance.

Dimensions are nominal reference values, not a stock list or a guarantee that every material/size combination is available. Specify the named standard and edition, material, finish and quantity in your enquiry. Manufacturing and inspection follow the agreed order or approved drawing.

Straight answer

How to specify a foundation bolt assembly

Foundation bolts are ordered to a civil and equipment interface, not just a thread size. Send the base-plate and foundation drawings, anchor pattern, material grade, projection and template requirement. Lohar Forging can review drawing-based bolt enquiries; engineering of the concrete anchor system remains with the project designer.

Product scope

J, L, straight and plate anchor configurations

J-shaped, L-shaped, straight and threaded-end arrangements are common drawing families. The correct pattern depends on the anchor design, installation method and space available below the base plate. A bent anchor should not be substituted for a headed or post-installed anchor without project approval.

Engineering selection

Thread, projection, embedment and template layout

Confirm the bolt circle or coordinate layout, overall and embedded lengths, projection above concrete, threaded length, plate and washer dimensions, sleeve or template and grout allowance. The designer must evaluate tension, shear, edge distance, concrete strength and installation tolerances. Accurate setting-out is as important as the steel part.

Technical analysis

Why anchor shape and embedment must match the design

Anchor geometry is controlled by the approved civil interface. Projection, template coordinates and grout thickness should be checked together before dispatch. An anchor with the correct steel grade can still be unusable when it misses the base-plate holes or lacks the specified embedment. Site installation and concrete capacity remain the designer’s responsibility.

Manufacturing review

Customer drawing review before manufacturing

A manufacturing enquiry is checked against drawing revision, material specification, bend geometry, threading and finish. If a template or matched nut-and-washer set is required, show it as a separate line item. Dimensional inspection can focus on anchor spacing, thread fit, overall length and projected length before dispatch.

Evidence and inspection

Inspection, traceability and order documentation

Ask for material documentation, dimensional records and coating records when the project requires them. Do not infer anchor capacity from rod grade alone: base plate, concrete and embedment design govern performance. Installation torque and grout sequence should come from approved civil and structural procedures.

International procurement

Export specifications and packing details

For international EPC orders, use a controlled drawing register and clearly label each anchor set by equipment tag or foundation number. Specify metric/inch units, destination packing, template details and the exact document dossier required for site acceptance.

Ready to enquire?

Technical RFQ checklist

A complete first enquiry helps us discuss fit, supply scope and documentation without guessing.

  • Approved foundation and base-plate drawings
  • J, L, straight or custom anchor pattern
  • Diameter, pitch, length and projection
  • Material grade and coating
  • Nut, washer, sleeve and template
  • Anchor coordinates and tolerances
  • Quantity, tags, documents and destination

Related product families

Choose the page that matches the component, rather than treating different fasteners as interchangeable.

Engineering reference

For specification research, see ASTM F1554 — anchor bolt specification. This external reference does not mean that every listed product is certified to it. Confirm the applicable edition, product rating and required documents in your approved purchase specification.

Quick Summary

Foundation bolts connect equipment or structures to a concrete foundation. Their shape, embedment and setting-out must follow the engineer-approved design.

Key Takeaways

  • Approved foundation and base-plate drawings
  • J, L, straight or custom anchor pattern
  • Diameter, pitch, length and projection
  • Material grade and coating

Made to your approved requirement

Custom foundation bolts: send your drawing or layout

For a custom part, email your drawing or layout to sales@loharforging.com, send it on WhatsApp, or call +91 98330 72266 to discuss the requirement. We confirm the drawing revision, material, finish, quantity and inspection scope before manufacturing. Custom dimensions come from your approved drawing; the reference tables below do not define a custom component.

  • J, L, straight, plate or specified anchor pattern
  • Thread diameter, pitch and length
  • Overall length, projection and embedment from approved design
  • Template, sleeves, plates, nuts and washers
  • Material, finish, quantity, drawing revision and documents

Company and order verification

Manufacturing information and documents

Product information is maintained by Lohar Forging & Engg. Works, Mazgaon, Mumbai. This page was updated on 14 November 2026 with standard-reference dimensions and ordering guidance.

See our company and manufacturing profile and inspection and documentation process. The company publishes Government of India IEC 0315056487; view the published IEC document. The scanned record is historical; confirm current company particulars and required documents with the sales team.

An IEC is an import/export registration, not a product test certificate. Request the applicable material, dimensional, coating or lifting documentation for your exact order. Confirm the scope and validity of any required quality-system certificate with the team.

FAQ

Foundation Bolts: frequently asked questions

Need a specific answer?

Send your drawing or requirement — we reply within 24 hours.

WhatsApp
Can I order foundation bolts from a thread size only?

No. The foundation design must define anchor pattern, embedment, projection, material, finish and associated hardware. Share the approved drawing.

Do you supply anchor templates?

Include the template drawing and quantity in the RFQ. Availability and manufacturing feasibility can then be confirmed with the bolt set.

Who determines the anchor load capacity?

The project structural or civil engineer should design and verify the complete anchor system, including concrete, edge distances, base plate and installation.

What details are needed for foundation bolts?

Send approved foundation and base-plate drawings, anchor pattern, diameter, projection, material, finish, nuts, washers, template details and quantities. The structural designer must confirm anchor capacity.

Are all foundation bolts made to one standard set of dimensions?

No. A named standard defines a specific pattern and dimensional scope. J, L, straight and plate assemblies have different geometry. The customer drawing defines project-specific length, projection, embedment and template spacing.

Do you decide custom foundation bolt measurements in advance?

No. Send the customer-approved layout or drawing by email or WhatsApp. Lohar reviews the specified dimensions and manufactures against the agreed requirement.

Does the dimension table establish anchor load capacity?

No. The structural designer checks the complete system, including concrete, embedment, edges, spacing, base plate and loading. This reference table describes geometry only.

Explore more

24 hour quote response

Need Forged Hardware Fast?

Get a quote within 24 hours. Bulk & export enquiries welcome across our markets.

WhatsApp Us

WhatsApp

Hello! Need help with forged hardware, bulk orders or a quick quote? Chat with us on WhatsApp and we’ll respond fast.

Open chat